With the winter season quickly approaching, central heating for your home becomes a priority. In order to keep your home warm, all components of your central heating system must be in proper working order. However, there are some typical faults with the system that tend to happen at the worst possible time. One such common problem is frost damage, which can damage and sometimes destroy boilers and pipes.
In the past, the central heating system was set up so that the frost thermostat was placed near the boiler. It was responsible for turning on the boiler as the ambiance temperature dropped below the determined level and heat was needed. The thermostat also stopped the boiler when it detected the air temperature was at an appropriate level. Many times the thermostat detected heat leaking from the boiler or the pipes and immediately turned off the system to conserve energy.
In recent years, the boiler and nearby pipes have been insulated much better (thus effectively saving energy) that the frost thermostat can no longer effectively determine when the air temperature has reached the requested degree. This can prove to be problematic, as it may lead to overheating.
A pipe thermostat can be one simple solution. This device is positioned directly on the boiler return pipe. This thermostat measures the pipe temperature and shuts off the boiler in the event of overheating. There are a number of new products that contain both a frost thermostat and low limit pipe thermostat. These products provide the ability to control room temperature and provide protection from frost.
Set up and installation of the thermostats is easy and user friendly. Directions for installation and wiring arrive along with the product, all in one kit. Frost thermostats are commonly set to 5C and pipe thermostats are usually set to 25C. If you have additional exposed pipes (e.g in the garage), extra thermostats can be bought to secure your central heating system completely.
If the pipe thermostat fails to meet your needs, there are other solutions. A fully programmable room thermostat is one option. These devices can be installed in a number of locations throughout your home, usually in a living room or bedroom. Their job is to measure and monitor the temperature of the room. The thermostat can be set to change the room temperature several times a day, depending on the homeowner's needs. There are several kits that operate by means of radio signal, from the thermostat to the boiler. These Radio Frequency (RF) thermostats require no wiring, which makes them very easy to install.
Thermostats are an important element of your home heating system but, there are other variables that impact your heating efficiency. By sectioning the home off into zones, waste can be avoided. The use of zones, allows you to focus the heat where you need it most. More populated areas can be kept warmer than empty rooms that do not require as much heating. This minor change can produce great results. Not only will heating bills be lower but, system efficiency will be greatly improved.
In the past, the central heating system was set up so that the frost thermostat was placed near the boiler. It was responsible for turning on the boiler as the ambiance temperature dropped below the determined level and heat was needed. The thermostat also stopped the boiler when it detected the air temperature was at an appropriate level. Many times the thermostat detected heat leaking from the boiler or the pipes and immediately turned off the system to conserve energy.
In recent years, the boiler and nearby pipes have been insulated much better (thus effectively saving energy) that the frost thermostat can no longer effectively determine when the air temperature has reached the requested degree. This can prove to be problematic, as it may lead to overheating.
A pipe thermostat can be one simple solution. This device is positioned directly on the boiler return pipe. This thermostat measures the pipe temperature and shuts off the boiler in the event of overheating. There are a number of new products that contain both a frost thermostat and low limit pipe thermostat. These products provide the ability to control room temperature and provide protection from frost.
Set up and installation of the thermostats is easy and user friendly. Directions for installation and wiring arrive along with the product, all in one kit. Frost thermostats are commonly set to 5C and pipe thermostats are usually set to 25C. If you have additional exposed pipes (e.g in the garage), extra thermostats can be bought to secure your central heating system completely.
If the pipe thermostat fails to meet your needs, there are other solutions. A fully programmable room thermostat is one option. These devices can be installed in a number of locations throughout your home, usually in a living room or bedroom. Their job is to measure and monitor the temperature of the room. The thermostat can be set to change the room temperature several times a day, depending on the homeowner's needs. There are several kits that operate by means of radio signal, from the thermostat to the boiler. These Radio Frequency (RF) thermostats require no wiring, which makes them very easy to install.
Thermostats are an important element of your home heating system but, there are other variables that impact your heating efficiency. By sectioning the home off into zones, waste can be avoided. The use of zones, allows you to focus the heat where you need it most. More populated areas can be kept warmer than empty rooms that do not require as much heating. This minor change can produce great results. Not only will heating bills be lower but, system efficiency will be greatly improved.
About the Author:
Tal Potishman, editor of Heating Central, writes articles about boilers, central heating, London plumbers, underfloor heating and solar thermal. He specializes in helping save money by advising on efficient heating.
0 commentaires:
Enregistrer un commentaire